The last few eventful months

I haven’t managed to write a blog post for quite some time. This is mainly because during weekends I’ve been busy and during evenings I’ve not been able to motivate myself! Anyway, I have a few moments now, and a lot to summarise, so here goes!

Sarah and I have had several enjoyable days (and an evening) out since the last blog post on 29 March 2009! Most of these occasions are summarised below.

AJS & Matchless Owners Club North Weald Section Meet

Every so often, the AJS & Matchless Owners Club has a meeting where various sections of the club meet up to say “Hi” and discuss all things motorcycle-related. This particular one was at North Weald Airfield where we met up with another section or two. I forget which ones though, I’m afraid!

North Weald Section Meet

As you can see from the above photo, there were quite a few bikes there – perhaps 80 in total; they’re not all visible in this particular photo though.

All in all, a very enjoyable day! I got to meet lots of new people and was able to sit within feet of the taxiway to the runway in use for that day. I even saw a Spitfire power itself down the taxiway to the end of the runway just before throttling up its wonderful Rolls Royce Merlin Engine and taking off into the distance!

Photos of the North Weald Section Meet can be found here.

Sandringham Arts and Crafts Fair

I don’t really have a general photo to summarise this event, so here’s a rather specific one:

Sandringham Arts and Crafts Fair

This event was exactly what you would expect from an Arts and Crafts Fair. It had honey, jams, wood turning, wood carving (shown above!), cookery and various other things. We also spent a few hours in Hunstanton after visiting the fair to have Fish and Chips by the sea, which was also quite enjoyable and relaxing!

Photos of Sandringham and Hunstanton can be found here.

Cambridge Museum of Technology Steam-Up Day

For Sarah, I think this day was decidedly average. For me, however, it was great!

Steam Engine at Cambridge Museum of Technology

I’ve been to the Cambridge Museum of Technology many times, and I can highly recommend it to anyone interested in pumping engines, steam engines, big single-cylinder gas engines and all things industrial. On this particular day, they had the main big boiler fired up and most of the servicable engines running. They also had a model tank club visiting with very accurate scale models of various military vehicles (mostly tanks, of course!) which they were remotely controlling around the site.

Scale Model of Tank at Cambridge Museum of Technology

Photos of our day at Cambridge Museum of Technology can be found here.

Videos of our day at Cambridge Museum of Technology can be found here.

Cottenham Yesteryear Road Run

On 19 April 2009 the Cottenham Yesteryear Road Run took place. This is a charity event raising money for MAGPAS. 400 or so classic and vintage cars, motorcycles, tractors, trucks and military vehicles took place in the road run which went from village to village showing residents and visitors  all the vehicles and also collecting money for MAGPAS, as mentioned above.

Motorcycles at the Cottenham Yesteryear Road Run

As of 20 June 2009, this year’s Road Run had collected £12,000 for MAGPAS, and I’m glad to have contributed at least slightly to something contributing to such a good cause!

Photos of the 2009 Cottenham Yesteryear Road Run can be found here.

Videos of the 2009 Cottenham Yesteryear Road Run can be found here.

FBHVC Old Vehicle Drive It/Ride It Day

The FBHVC Drive it/Ride It Day is not an organised event as such. It’s a day where the Federation of British Historic Vehicle Clubs (FBHVC) request that as many historic vehicle owners get their vehicles out on the road for the day to show to the nation that these vehicles exist and are still driveable/rideable!

Sarah and I decided to ride to a pub in a nearby village to have lunch by the river and to then ride home, and I must say, it was another great day! :-)

AJS & Matchless Owners Club Motorcycle Run

Throughout the year, various members of the Fenrunners section of the AJS & Matchless Owners Club organise motorcycle rides around the county (and beyond!), and this ride was no exception. We met at The Chequers Inn at Wrestlingworth before setting off on a 75 mile route, finishing back at the Chequers Inn again! These 75 miles were ridden in one continuous stretch, which, despite being the longest non-stop ride I’ve ever done, was very enjoyable!

6 of us turned up at the pub in the first place, but within 500 yards or so, 2 people had broken down, leaving only 4 of us to take part in the run. Luckily enough, though, despite 2 bikes breaking down within that short distance, they were both up and running again by the time we got back and were both ridden home later that day with no problems!

I have no photos of this event, I’m afraid, but I do have the route as recorded by my GPS if you are interested!

The Nesting Blackbird

This wasn’t an event at all, but it is worth mentioning!

At the beginning of April, Sarah noticed that a blackbird was nesting on top of our water butt, 5 feet off the ground, in the corner between the fence and trellis running down the front edge of the canopy in our back garden, and around 12 feet from out back door, which is used all day every day!

The blackbird didn’t seem to care about Sarah and I going in and out of the back door and using the garden for BBQs etc… or even hanging washing out on the line which was around 4 feet away from her nest! I was also able to setup my tripod and camera behind the trellis pointing into the nest, about 12 inches away, zoomed right in to take some quite impressive photos.

Blackbird in the Nest 1

The blackbird then laid 5 eggs!

Blackbird eggs in the nest

At this point, Sarah and I looked up various facts about the blackbird and learned that these eggs were going to hatch in around 2 weeks. Before that time, however, roughly 3 weeks after the blackbird started nesting and 1 week after the eggs were laid, the blackbird appeared to have deserted the nest entirely!

After 24 hours of staying away to give her a chance to come back, we realised she wasn’t coming back and upon looking into the nest again, we realised that there were now only 2 eggs remaining.

I would like to add that we really don’t think it was us that scared the blackbird away as we had never attempted to touch the nest or disturb the plants growing around it – the gap in the plants through which the photos were taken was there naturally, and the blackbird had never been bothered by us in the past at all!

A couple of days later, there was only 1 egg left, and it was slightly cracked from the outside, so we figured something had found the nest and taken the eggs, sadly.

Anyway, we do seem to have either the same blackbird, or a different one, nesting in a new spot in the garden now, and this time we’re not going near it, just in case. I guess we’ll see what happens in due course!

More photos of the blackbird, the nest, the eggs and a few other birds in our garden can be found here.

Jampot Spares Limited Open Day

JSL Open Day

Although this was a very enjoyable day, it did start off badly!

The Open Day at JSL is an event often visited by lots of club members. A lot of these members I know from the club web site as they have helped me get the bike on the road over the last year or so, but I’ve never actually met them. This event was going to be a perfect opportunity for Sarah and I to not only meet these great people, but to turn up on the motorbike so they can actually see the bike they’ve hearing and talking about so much.

However, that, sadly, was not to be. Having wheeled the bike out into the open, started it up and got kitted up, I rolled it off the stand, pulled in the clutch, put it into first gear, and the engine stopped. The exhaust valve had jammed open again, like it did early last year.

We therefore attended the JSL Open Day by car. As I said, it did turn out to be a very enjoyable day, but for the first half an hour or so, before we arrived, I did feel rather annoyed, to say the least!

Photos of the JSL Open Day can be found here.

Videos of the JSL Open Day can be found here.

Classic Bike Show, Stanford Hall

I attended this show by car, as it would have been rather a long and tedious journey by bike! It was another good day with perhaps a hundred or two classic bikes on show, plus another 1,000 or so in the car park field, ranging from vintage pre-war bikes to modern Hondas and Kawasakis.

Stanford Hall Classic Bike Show

The Photo above shows the AJS & Matchless Owners Club stand which, as ever, was nicely presented!

I didn’t buy anything other than a mug, pin badge, cleaning cloths and a tube of Autosol on this particular trip, but there were an awful lot of things to buy, ranging from almost complete motorcycles to individual nuts and bolts. I highly recommend it to anyone wanting to admire some old bikes and to also spend a couple of hours trawling through the autojumble stalls!

Photos of the Classic Bike Show can be found here.

The Sidestand Spring and The Hurt Finger!

I have known for a very long time that the spring holding the sidestand up on the Matchless was both stretched slightly, and hooked onto the wrong place on the frame.

A fellow club member (thank you, Peter!) kindly donated a new sidestand spring to me and showed me, on his bike, where the holes in the frame should be to hook the spring into, so armed with that information I headed into the garage to fit the spring!

I won’t go into too much detail here, but in summary, the spring is quite tough. Having hooked one end into the frame underneath the bike, I began to pull the spring towards the side stand to hook on the other end. In doing so, the spring slippped out of my grip and the hooked end went into the skin on the bottom of my finger and pulled my hand back under the bike. Having looked under the bike to see what on earth I’d just done, I saw the end of the spring trying to push through the skin on the top of my finger!

I quickly removed the end of the spring (which had gone roughly 15mm into my finger!) and made my way into the kitchen whereupon I cleaned it up and sat down on the sofa for Sarah to kindly bring me a cold glass of water!

Needless to say, I felt rather ill for the next 20 minutes, but there was actually very little pain, almost no bleeding, and 7 days later it was as if it never happened. Very strange…

Souldrop Open Evening & BBQ

A new motorcycle workshop has opened up in Souldrop recently and they decided to have an Open Evening and BBQ, which Sarah and I, of course, attended!

Souldrop Open Evening & BBQ

It was a great evening! Roughly 20 people turned up, most of them on two wheels, there was plenty of food, all barbequed by myself ( :-) ) and it was a late, but very enjoyable evening!

Photos of the Souldrop Open Evening & BBQ can be found here.

AJS & Matchless Owners Club Crosskeys Pub Inter-Section Meet

Similar to the North Weald Section Meet mentioned earlier in this post, this event took place at The Cross Keys in Norfolk.

AMOC Crosskeys Section Meet

It was an incredibly sunny, and rather warm, day and in total I rode 134 miles! We met some more new people, spent a few hours chatting about motorcycles, had a great pub lunch and then rode home!

I must say though, 134 miles in one day, with the last 65 of them being non-stop, is quite tiring, especially at an average speed of 30 mph with a top speed of 45-50 mph! The last 65 miles, for example, took 1 hour, 54 minutes!

It was thoroughly enjoyable though, so I’m not complaining! :-)

Photos of the Crosskeys Section Meet can be found here.

Somersham Carnival

As of the day this blog post was published, the last event we’d been to was Somersham Carnival.

Somersham Carnival

I’ve been to Somersham Carnival nearly every year of my life, which isn’t so strange considering I grew up in the village!

There’s not a lot to say about the carnival really. It’s exactly what you would expect from a village carnival; classic cars, floats, a parade around the village, Somersham Town Band, an arena in the field in which various displays occur and a generally good day out for adults and children alike!

This year, however, I took along the motorbike for the first time ever. The bike itself has been in the parade and displayed in the field before, perhaps 15 or so years ago, when my Grandad still owned it, but this time it was my turn.

The other thing to mention is that I won the “Best Motorcycle” award, as shown below!

Best Motorcycle Award from Somersham Carnival

It is important to note, however, that my motorcycle was the only one there, so you could argue that my bike was also the worst bike!

Anyway, as a few people have already said, an award is an award, regardless of how it was won!

Photos of Somersham Carnival can be found here.

What a disaster!

Well… yesterday was the day of the first classic motorcycle run of the year for the Fenrunners section of the AJS & Matchless Owners Club and I, of course, attended!

The weather was pretty awful, the forecast was even worse and it wasn’t very warm either, but nevertheless a few dedicated club members turned up for the run at the Tesco store just north of Cambridge.

The run was basically from the Tesco store to Mildenhall, for a warm pub lunch and then home (obviously via some convoluted route that actually makes the run worth doing!), but sadly, I didn’t quite make it that far…

In total, including the journey from my house to Tesco, 46 miles were planned there, and probably another 46 miles or so home again, totalling 92 miles for the entire day. However, all in all, I rode a grand total of only 39 miles!

As you will know from reading the rest of my blog (assuming you actually do, of course!), my own bike is still being put through the 35mph run-in period having had a new piston and rings, so I’m currently attending club runs on a fellow club member’s (Peter’s) bike which he has very kindly lent me – a 1955 AJS… not sure of the model, but it’s also a 350cc heavyweight like my own bike, just 11 years older. Very good condition too, I might add!

Anyway, as you can see from the map below (click to enlarge), the plan was to meet up with a couple of local club members in Sainsbury’s car park in Huntingdon (at point A), to then ride to the starting point of the run (at point B), and then to ride the route shown to Mildenhall (at point D). However, frustratingly, I couldn’t go any further once I reached point C! So close, and yet so far…

The Route of 28 March 2009

Point C (the layby where I stopped) can be seen below:

The Layby

As you can see, it’s in the middle of nowhere!

As we were riding along this long straight road (from bottom to top as you look at the above photo), there was a horrendous sidewind which was gusting a lot. It wasn’t gusting to the point where it was dangerous, and we were nowhere near being blown into the oncoming lane, but it was certainly significant. It was also raining. It was roughly at this point I started to look forward to the warm pub, the hot pub lunch and the opportunity to dry off slightly! Maybe that was my mistake…

With a sidewind, as any motorcyclist will know, it can feel a bit like you are riding on jelly, you are gently swept from side to side as the wind comes and goes and as soon as any gust disappears, you find you are still steering into it slightly, so suddenly move the into the gust and have to compensate again by steering in the other direction. It’s pretty much the same as in a car, but you feel it a lot more on a bike!

Anyway, with all this happening, and the rain coming down, albeit lightly, I noticed that even when the gusts stopped, it still felt a little like I was being blown around. It wasn’t until I noticed this happening a couple of times (in the space of 15 seconds or so) that I realised that if I really was being blown around, it was only happening at the back of the bike!

It was at this point I decided I ought to pull over and see what was going on – was the wheel coming loose? Was something else wrong? Was it really just the wind?

Well, it turns out I had a puncture in the rear tyre, caused by a metal fencing staple!

So, that was it – the run was over! 3 or 4 other club members pulled over too, to see if everything was OK, and I must thank those people again for doing so! :-)

Now, canisters of compressed air mixed with liquid rubber-like stuff exist which can be squirted into the valve to both pump up the tyre and seal the puncture, but (a) they don’t always work, and (b) nobody had one anyway, so that clearly wasn’t an option!

I decided, at that point, I ought to find out if Peter’s insurance (on which I am a named driver) had breakdown cover. I spent 30 minutes or so phoning 118118 and all the numbers they gave me, to no avail, and eventually phoned up a work colleague who looked up the number online for me! So much for 118118! It turns out that Peter’s insurance does have breakdown cover, and so 45 minutes later, the truck arrived and took me and the bike home!

By the time the breakdown truck arrived though, I had then been stood in the windy layby for 1hr, 15 mins, 45 minutes of that was spent with Neville and Mark from the club, so a big thank you to them! During that time, we had even stronger wind, more rain, hailstones twice and countless cars zooming past spraying us all with dirt and water! The photo of this location, at that time, can be seen here:

Pete's Bike With Flat Tyre

I must admit, I’ve brightened up that photo a bit… it almost looks bright in the above photo, but believe me – it wasn’t!

And here is the bike being loaded up onto the truck having been carefully strapped to the loading device:

Pete's Bike Being Loaded Up With Flat Tyre

Once I got home, there had been half a warm turkey delivered from Sarah’s parents (Sarah had been at home during this short trip), which Sarah kindly made into a sandwich (as I never made it to the pub and really was getting kinda hungry by this point!) and later on that afternoon Peter phoned me to say he was more than happy to sort out the puncture, as it’s his bike and therefore his problem, and as much as I disputed the latter, he wouldn’t back down, so he later turned up with his trailer and picked up the bike. So, thank you to Peter too, not only for lending me his 54 year old bike, but for also offering to repair the puncture before letting me have the bike back yet again!

Hopefully I’ll have beter luck on the next run…

The bike is finally up and running, but that means the run-in period has begun…

Well… after a long search (which I’ll attempt to summarise below) and a fair amount of effort, the Matchless is up and running again! It does need to be run in, however, which is going to involve riding 500 miles at 30-35mph! This, of course,  is far from ideal, but it must be done to ensure long life of the new piston rings, and no engine seizing! Anyway… onto the story since the last post.

The piston I picked up from AMC Classic Spares, although the correct diameter, was definitely the wrong one (this was not their fault, I might add) and although it could potentially be milled out, I decided to wait and see if a proper, original, BHB piston was ever going to turn up. This piston is therefore sitting on my shelf right now, waiting for me to sell it back to AMC Classic Spares if they’ll take it! :-)

The main problem was that even if it could be milled, the metal underneath the milled area would have been very thin, and the reinforcement ridges built into the casting of my original piston don’t exist on this new one, so it would be far from ideal in this situation.

Having almost given up on the new piston, I started to phone the rest of the places on my list, in the UK and abroad! I even, accidentally, woke up someone at home in Australia at 4am, having got the timezones 4 or 5 hours out compared with the UK! I knew it was morning over there, given that it was evening over here, but I wasn’t sure how early in the morning it was. I figured that given this was a business, if the business was closed I could leave a message, but it was actually a house phone, so there it was – the call at 4am!

After phoning all of the places on my list though, I gave up hope of finding one via the web or over the phone and started hoping the adverts placed in the various magazines might throw something up.

Before these were even published though, I received a response on the club web site from a club member in Canada who had an original BHB piston, part number 030148, which had been sitting on his shelf since 1977, which I was welcome to have if I wanted!

So, this piston was posted to the UK, and 12 days later it arrived. Once cleaned up a bit, I revealed the same part number as my cracked piston!

Excellent! :-)

So… into the bike it went, and after 2 hours in the garage, on the 5th kick, the bike started!

The next day I set off around town for a couple of miles to see how the bike ran, and to begin the run-in process, but once the bike warmed up, there was a distinct rattle from somewhere in the engine.

I adjusted the tappets, the day after, and went out again to find that the rattle was still there. When I got home, I adjusted the tappets again (while the bike was still warm this time!) and since then, I think the rattle has gone away.

I’m 35 miles into the run-in period now, and I still can’t hear the rattle, so I guess it really has gone!

The trouble is… I’m now questioning both my memory of the rattle, and my audio observation skills. Perhaps the rattle is still there, and I just can’t hear it for some reason… perhaps the rattle really has gone… perhaps I’m over-analysing things again!

I guess I’ll know for certain when I have a second opinion from someone who actually knows about these things! :-)

The cracked piston and the not-quite-right replacements

Right, regarding the cracked piston, it’s bad news so far unfortunately…

To start with, I’ll actually show you the problem…

The Cracked Piston (Close-Up)

As you can see, on the top edge of the piston there is a crack running vertically from the top of the piston edge, down through the top two ridges. This is what makes this piston unfortunately useless.

So anyway… the brand new piston that was kindly posted to me from the chap in Derbyshire was sadly the wrong diameter – I need a 72mm diam. piston, and this was 74mm. That piston was therefore sadly posted back.

I then started making phone calls again and found that there a 72mm piston at AMC Classic Spares. I drove over there Saturday morning to compare the piston with my original one, and to hopefully make a purchase.

When I arrived, the piston was the correct diameter (72mm), it had the correct gudgeon pin diameter and distance from the crown, and everything about it was correct apart from the grooves cut out of the crown for the valves to drop into as they open.

Nevertheless, I purchased the piston and set about assembling the bike carefully, minus the gaskets, to see if the engine would turn over, and sadly it doesn’t. The inlet valve touches the top of the piston, meaning I would have to have the piston milled out to the correct size. The problem with this approach, however, is that there doesn’t seem to be enough metal on the underside of the piston to mill into and the strengthening ridges on the underside of the old piston to account for the deeper grooves don’t exist on the new piston so unfortunately, I’m back to square one again!

Just in case there are any fellow motorcyclists reading this blog, please get in touch if you think you can help! You can contact me through my 1966 Matchless G3 site! :-)

Also, here are a few pics of the original piston so you know what i’m after…

1966 Matchless G3 "short-stroke" piston - 72mm, 85.5 stroke

1966 Matchless G3 "short-stroke" piston - 72mm, 85.5 stroke

Top of the old piston

Top of the old piston

The inlet valve groove is much larger than the the exhaust groove, as you can see. In the above photo, the inlet groove it at the bottom of the photo.

So… there we go - I still have a cracked piston, I still don’t have a replacement, but I’m ever hopeful that I might stumble across one soon enough. Let’s hope so, anyway!

Fallout 3 (again), my Xbox’s blog and the cracked piston…

Before I get onto the situation with the Matchless, I’ll start with Fallout 3 (mentioned in my previous post) and my Xbox’s new blog!

First of all, Fallout 3… I’ve finished it! :-)

In the end, it took just over 75 hours from start to finish and I’m glad to say I kept “good karma” throughout the game and instead of making my companion enter the highly radiated room in the last moments in order to activate the purifier, I went in myself, thereby paying the ultimate price for the greater good.

This is, of course, still a game, so no price was paid at all. I even borrowed the game from a friend, so literally no price has been paid at all!

I also stick with my previous statement that this is a game I strongly suggest you get hold of if you have the equipment necessary to play it!

So… onto the Xbox’s blog!

There is a site called 360voice.com which acts as a way for your Xbox 360 games console to write it’s own blog posts every day about your gaming habits, achievements gained and other aspects of gameplay.

In actual fact, the games console itself has nothing to do with writing the blog posts (as you may have worked out already!). 360voice.com simply looks at your stats each night and generates a blog post based on that information, which looks suspiciously like it was written by the Xbox itself. It’s kinda funny, and a novelty to have, so here’s a link if you want to have a read: http://360voice.gamerdna.com/tag/fishsponge

Right… now it’s time to talk about the Matchless

After yesterday’s post, you will know that the piston rings were worn out on the motorbike and needed to be replaced, so this morning I took all the parts to Bill’s house where, after cleaning the valves, re-grinding the valve seats, putting the cylinder head back together, finding and manufacturing an alternative solution to the broken sleeve nut, removing the old piston rings and cleaning out the grooves we went to put in the new piston rings!

Upon putting in both parts of the oil control ring, we discovered it wasn’t rotating as freely as we’d like, so Bill took the ring off and we went to examine the groove a little closer.

It was at this point Bill informed me that the piston appeared to be cracked.

Upon hearing this news, I realised that this was something of a disaster. It’s good that we found it because a cracked piston could disintegrate in the cylinder, destroying large chunks of the engine in the process, but it’s bad that it was cracked because original pistons for a 1966 Matchless G3 350cc short stroke are phenominally hard to find.

I coincidentally inquired at the Spares Scheme while I was there the other day to see if they had any, and the answer was, not surprisingly, “no”!

So anyway, Bill phoned a friend of his to see if he could give any leads as to where to obtain one, and believe it or not, he had a brand new one, in a box, never used, with all the rings, the gudgeon pin a the various other bits you need to install a new piston!

This was unbelievable!

So… this kind chap is going to post the piston to me, I’ll post a cheque to him and hopefully, with a bit of luck, I’ll be up and running soon! :-)

The one thing to note, however, is that with a brand new piston etc… it has to be run in, which involves riding 500 miles no faster than 35mph. Given that the first motorbike run of the season is at the end of March, that gives me around 4 weeks to achieve 500 miles at 35mph or slower if i’m going to make that first run!

Providing the weather holds out, the evenings aren’t too dark, and the bike goes back together as well as I hope it does, that is just achievable in my opinion. A relatively tall order, but just about achievable.

I’ll keep you updated!

Fallout 3, piston rings and the ruined sleeve nut!

I have been playing games on my Xbox 360 a lot since Christmas, mainly because it’s winter and there’s not a lot else to do indoors that’s quite as much fun!

Other than Forza Motorsport 2, Pure and A Kingdom for Keflings I’ve been playing a lot of Fallout 3. I’m over 60 hours into the game now and estimate that I have somewhere between 5 and 10 hours remaining before I reach the end.

For those who don’t know, Fallout 3 is an action role-playing game which takes place in the year 2277, 200 years after the nuclear war that devastated the game’s world in an alternate post-WW2 timeline. It’s not a particularly cheerful theme, but it works really well as an action RPG.

The trailer for Fallout 3 is below.

I can’t get rid of the advert that appears after 12 seconds, I’m afraid, but if you click the small grey “x” on the right hand side of the advert when it appears, it should disappear :-)

NOTE: If you can’t see the video above, click here

So anyway, this is a truly excellent game in my opinion and I strongly suggest that if you have the equipment to be able to play such games (a half-decent PC, Xbox 360 or Playstation 3) you get hold of this one!

So anyway, onto the Matchless…

Although I have been riding the motorbike throughout winter (on dry days, after the salt has been washed off the road) ever since last summer the piston rings have been worn out.

More specifically, the bike was burning oil, and both valves were perfectly OK (as per the post “It does appear to be working, but now there’s rain!“), so that leaves only the piston rings!

On Monday this week, I started to take the top of the engine off again, on Tuesday the local expert and friend of mine, Bill, came over to lend a hand and to examine the piston rings, the piston itself and the cylinder and we determined that the piston rings certainly needed replacing. In fact, the scraper ring (which is supposed to keep the oil below the piston) looked like it wasn’t doing anything at all, so there was certainly a problem.

So, off to Kettering I went, on Tuesday afternoon, to speak to John about a sleeve nut (which I’ll come to in a minute), Rick about a new set of piston rings and Jim about a gasket set, which I’ll need to put the bike back together, of course!

Well… I got the gasket set, there’s no such sleeve nut as the one I need, and Rick was at home!

Not to worry though… John phoned Rick, who happened to have the piston rings I needed at home (thanks, Rick!) and was willing to have me pop over on my way home to pick them up!

Rick Edwards, by the way, aka “Piston Ring King” has his own blog here if you are interested, and his knowledge and piston ring collection are like none other, so get in touch if you need anything!

Anyway, regarding the sleeve nut, there is a bracket on top of the engine that secures the top of the engine to the frame, and this bracket is held on with 2 nuts that go on the tops of the double-ended bolts that go into the top of the rocker box, and another nut and bolt that goes through the frame itself.

However, the rear nut was stuck fast when I came to remove it, and was already rounded off due to many years of attempted removal in the past, and to cut a long story short(ish), I had to take a drill to it in order to remove it.

This, unfortunately, left the sleeve nut ruined:

Ruined Sleeve Nut

You can’t really tell from this angle, but the washer is stuck fast to the underside of the head, and the head is completely trashed, so basically, I need a new one.

The trouble is, the combination of parts that this sleeve nut is part of seem to be non-standard and therefore impossible to replace, so an alternative solution is required (which Bill and I will hopefully figure out tomorrow)!

So there we go… that’s about all I have to write about at the moment, so I’ll leave you to go and read and bookmark Rick’s blog! :-)

I shall post another update once the bike is back together again.

An uneventful January (so far) and more wasteful packaging!

I haven’t written a blog post for almost a month now, and that is mainly because so far in January, absolutely nothing has happened! I shall therefore end my comments on January now and move on to another instance of wasteful packaging!

As you may know, from a previous blog post on wasteful packaging, I don’t like to see examples of particularly wasteful packaging. I find it quite annoying, and today it has happened again! I have attempted to mask out the supplier because, although I would like to “name and shame”, I feel it might get me into trouble, so for now at least, they will stay anonymous.

Here is the box that arrived:

Wasteful Packaging

As you can see, the box is around 8″ x 8″ x 1″. What do you think this might contain? A book? A calendar? A DVD? Probably not a CD, because they come in smaller boxes, right?

Well, upon opening up the box, we can see what it contains:

Wasteful Packaging 2

A USB memory stick!

Now, I must admit, this is a rather large memory stick, at 16GB, but given that the extra bytes of storage don’t actually make the device any larger physically, did it really need a box this big?

OK, I can appreciate the need for a business to have certain box sizes, because having too many box sizes available adds to the cost of everything, so this is probably the closest fit they could find in their store, but nevertheless, it is a shame to see so much cardboard wrapped around such a small device, as I’m sure you agree!

Minstresers, Popcorn and Christmas

I’ll start this post with “Minstresers”…

Minstresers

As you can see, this is a photograph of a Galaxy “Minstrel”, and a “Malteser” (made by Mars, I think).

Individually, they are great. Let’s not forget that fact.

However, together, eaten at the same time, they are amazing! We discovered this at University and decided to call the combined treat, the Minstrel-Malteser.

Obviously, this will never make an official product, but if you can get hold of both, I strongly suggest you eat them together and see if you like it!

OK, so next on my list is popcorn… My Aunt and Uncle gave Sarah and I an instant popcorn maker, which since Christmas we have used twice so far, so thank you for such a great present! :-)

I have even realised that I actually do like popcorn, after many years of somehow assuming I don’t like it!

There is only one problem with it (which is more user-error than a problem with the machine), which is that it always seems to produce 1 million times more popcorn than you think it will!

Popcorn Maker

The problem is that once you’ve turned it on, and it’s started producing popcorn, it just never stops!

The photo above is from our second attempt and trying to predict the amount of popcorn more accurately than the last, and as you can see, we failed dismally!

I think the problem is partly pasta syndrome*, and partly the fact that you never know how much of the corn will “pop”!

Nevertheless, this is a great present and I’m sure it will get lots of use over the years!

Now onto Christmas… doesn’t it seem like it came and went within minutes this year? It does to me, anyway. Even so, it was still enjoyable, and having 2 weeks off work has certainly helped me to become calmer and more relaxed generally in life!

Seeing all the family together was, of course, good, and among the gifts received were the helmet/bike camera (which I actually started using 2 months ago), a headset mic for my Xbox 360 console (to talk to other online players), a chocolate fondue set, various games, vouchers, cash and the usual selection of chocolates. I should also thank my Grandparents for the rather generous gift I received from them too. :-)

So anyway, this year, despite it seeming like it’s been and gone in an instant has been rather good.

On to 2009!

* “Pasta syndrome”, by the way, is what I call the problem whereby you can never judge the correct amount of pasta to cook – you always end up with not enough or way too much.

The AJS & Matchless Fenrunners Clubman of the Year 2008 award!

Last Monday night, I attended the monthly AJS & Matchless Owners Club Fenrunners section meeting and among the various things discussed and announced was the “Clubman of the Year 2008″ award (shown to the right).

Just so you are aware, this award is exclusive to the Fenrunners section of the owners club, and although I’m sure other sections of the club have equivalent awards, this one is for the Fenrunners section only.

As you can see, the award has been given to various people over the years, beginning in 1990. The more recent names are engraved in a plate on the back, due to a lack of space on the front.

So anyway, as you may have guessed from the fact that I’m writing this post, I’ve been given the award! :-)

There are actually two trophies associated with this award; the trophy with everyone’s names on, which gets handed from person to person each year (shown above, on the right) and the trophy with just my name on, which I get to keep for ever (shown on the left).

From what I can make out, all of the people who have been awarded this trophy in the past have contributed to the club in some way, and although I don’t personally feel as if I’ve had a chance to contribute a great deal yet, I guess I have!

The reason for the award being given to me, I think, is a combination of two things…

First of all, I was told at the trophy handover, it was due to me basically being so young, so enthusiastic and for basically attending every single event since I joined the club! I guess I’m exactly what the club needs, in the sense that the average age of club members is relatively high, and the club therefore needs people like me to keep the whole club going in years to come.

The other reason, possibly, is that all of the people who I think have contributed a lot more than me this year have already been awarded the trophy at some point in the past, and therefore can’t be awarded it again, so by some token, it was possibly awarded to me by default!

Nevertheless, I am honoured to have received the award, and given that I don’t remember ever having been awarded a trophy for anything in my life ever, it’s quite a nice surprise to suddenly have two, so thank you to all voting members of the AMOC Fenrunners section! :-)

Wasteful packaging – the latest instance!

Wasteful packaging is something that kinda bugs me. To put it into perspective though, I don’t lose any sleep over it, and I don’t find myself thinking about it at random times during the day, but when I see an instance of wasteful packaging, it is slightly annoying.

The other day, a work colleague ordered a 1.8″ hard drive for a laptop from an unnamed supplier. Admittedly, hard drives need some packaging to protect their internals, but I feel this particular one was packaged perhaps a little too much…

Needless to say, the hard drive went into the laptop, the cardboard box was recycled, but the foam will end up in landfill because it cannot be recycled!

What a shame!

RSS for Posts RSS for Comments